Daily Quiz 67

Daily Quiz 67

civil engineering mcqs, mcqs in civil engineering, mcqs of civil engineering, civil engineering solved mcq pdf, civil engineering mcqs pdf,civil engineering mcq questions, civil engineering mcq book,WRD Quiz, SSC JE Quiz, RRB Quiz, Rajasthan JE Quiz, Civil Engineering  MCQ, Mahpariksha Civil Engineering  Objectives, JE Questions civil engineering

This Daily Quizzes is made up for daily practicing objective type questions both technical as well as non technical. In this Quizzes Questions are added from previous year question papers such as Mahapariksha PWD, Mahapariksha Town planning, Mahapariksha Soil and Water Conservation Department, WRD, Rajasthan JE, ITI Lecturer, SSC, RRB, BMC, GATE, ISRO, MPSC, UPSC, APPSC, Metro and also from objectives types books . I hope this is helpful for your upcoming Exams ✌.

All the best for your all upcoming Exams 👍💐💐💐

👉  👈

👉  👈

👉  👈

👉  👈

civil engineering mcqs, mcqs in civil engineering, mcqs of civil engineering, civil engineering solved mcq pdf, civil engineering mcqs pdf,civil engineering mcq questions, civil engineering mcq book,WRD Quiz, SSC JE Quiz, RRB Quiz, Rajasthan JE Quiz, Civil Engineering  MCQ, Mahpariksha Civil Engineering  Objectives, JE Questions civil engineering

Daily Quiz 67

Q.1. ABC analysis which is used in inventory control system is based on which of the following principle? 

a) Harris-Wilson model

b) Pareto principle ✔

c) EOQ model

d) All of the above

Q.2. A line of true length 600 m when measured by a 20 m tape is reported to be 609 m long. The correct length of tape (in m) is

a) 19.50

b) 19.70 ✔

c) 19.90

d) 18.90

True Distance = l'/l x Measured Distance
600 = l'/20 x 609
l' = 19.70

Q.3. The number of simultaneous equations to be solved in the slope deflection method is equal to 

a) the degree of statical indeterminacy

b) the degree of kinematic indeterminacy ✔

c) the number of joints in the structure

d) none of the above

Q.4. A fixed beam AB is subjected to a triangular load varying from zero at end A to 'w' per unit length at end B. The ratio of fixed end moment at B to A will be

a) 0.50

b) 0.33

c) 0.67

d) 1.50 ✔

Fixed end moment AB = wl²/30
Fixed end moment BA = wl²/20
∴ ratio of fixed end moment at B to A will be 1.5

Q.5. A lacing column is designed to carry 500 kN axial load. The total transverse shear resisted by lacing will be 

a) 25 kN

b) 6.25 kN

c) 12.5 kN ✔

d) 15 kN 

Transverse Shear  = 2.5% of load = 2.5% x 500 = 12.5 kN

Q.6.  Shape factor is the property which depends, 

a) only on the ultimate stress of the material

b) only on the yield stress of the material

c) only on the geometry of the section ✔

d) both on yield stress and ultimate stress of material

Q.7.  What is the percentage of the fine aggregate of fineness modulus 2.6 to be combined with coarse aggregate of fineness modulus 6.8 for obtaining combined aggregate of fineness modulus 5.4 ?

a) 30%

b) 40%

c) 50% ✔

d) 60 %

Q.8. Which one of the following pairs is NOT correctly matched?

 

a) Visco-elastic : Small plastic zone material ✔

b) Strain hardening material : Stiffening effect felt at some stage

c) Orthotropic material : Different properties in three perpendicular & sections

d) Isotropic material : Same physical property in all directions at a point

Q.9. A metal bar of length 200 mm Is inserted between two rigid supports and its temperature is increased by 20°C. If the coefficient of thermal expansion is 3 x 10⁻⁶ /°C and E= 2 x 10⁵ MPa. then the stress in the bar Is

a) zero

b) 24 MPa

c) 48 MPa

d) 12 MPa ✔

σ = EαΔT
σ = 2 x 10 ⁵ x 3 x 10⁻⁶ x 20
σ = 12 MPa

Q.10. Area under the β-distribution curve is divided into two equal halves by a vertical ordinate through. 

a) Expected time ✔

b) Optimistic time

c) Mostly likely time

d) Pessimistic time

Q.11. Of the five members of an interview committee sitting in a row, B is left to E but right to A. D is sitting right to C but left to A. Find the one sitting in the middle.

a) B

b) A ✔

c) D

d) C

Q.12. In series one number is wrong. After searching the wrong number find out the correct number in its place. :   0, 9, 64, 169, 576, 1225 

a) 289

b) 666

c) 1369

d) 225 ✔

e) 125

If 169 is replaced by 225, then the series will be :
(1² - 1)² = 0
(2² - 1)² = 9
(3² - 1)² = 64
(4² - 1) ²= 225
(5² - 1)² = 576
(6² - 1)² = 1225

Q.13. Garden Reach Workshop is famous for

a) Railway engines

b) Automobiles

c) Shipbuilding ✔

d) Railway coaches

Q.14. Who has been appointed as the new Chairman of National Highways Authority of India (NHAI)?

a) Danish Kapoor

b) K K Sahoo

c) Sukhbir Singh Sandhu ✔

d) Yudhvir Singh Malik

Q.15.

                    

a) 2 ✔

b) 3

c) 1

d) 4

Multiplying elements of first three rows of respective columns will give the fourth row.
7 x 9 x 3 = 189
8 x 4 x 9 = 288
9 x 5 x 2 = 90

civil engineering mcqs, mcqs in civil engineering, mcqs of civil engineering, civil engineering solved mcq pdf, civil engineering mcqs pdf,civil engineering mcq questions, civil engineering mcq book,WRD Quiz, SSC JE Quiz, RRB Quiz, Rajasthan JE Quiz, Civil Engineering  MCQ, Mahpariksha Civil Engineering  Objectives, JE Questions civil engineering